View Profile: KurtEck - Trossen Robotics Community

1 Day Ago

KurtEck replied to a thread XL430-W250 Stop moving randomly in Software and Programming

Note: I see this question is now up on Robotis Forum:...

6 replies | 115 view(s)

2 Days Ago

KurtEck replied to a thread Dynamixel MX-64T Torque control with Arbotix in Arbotix, Microcontrollers, Arduino

I have not use MX-64T servos... Again suggest Robotis forum, although they may not understand anything about Arbotix and library... I would...

2 replies | 64 view(s)

2 Days Ago

KurtEck replied to a thread Question(s) torque control for ax 12a in DYNAMIXEL & Robot Actuators

Might try Robotis forum: http://en.robotis.com/service/forum.php Not sure what you have tried? Example setting:...

2 replies | 70 view(s)

2 Days Ago

KurtEck replied to a thread XL430-W250 Stop moving randomly in Software and Programming

Might help to know additional information, like what hardware are you using to drive the servo? OpenCM9.04, OpenCM9.04+OpenCM485 expansion,...

6 replies | 115 view(s)

6 Days Ago

KurtEck replied to a thread SetID Robotis - issue (I made a mistake) in DYNAMIXEL & Robot Actuators

First the link to Tician mentioned above. Again instructions on how to use sort of in thread message:...

8 replies | 251 view(s)

1 Week Ago

KurtEck replied to a thread Question(s) Dynamixels AX-12A on OpenCM 9.04 + OpenCM 485: how to send instruction packets in DYNAMIXEL & Robot Actuators

I am sort of confused here. If you are using Dynamixel SDK or Workbench it should handle everything for you. In that you should be able to send or...

3 replies | 148 view(s)

1 Week Ago

KurtEck replied to a thread SetID Robotis - issue (I made a mistake) in DYNAMIXEL & Robot Actuators

First thing: Arbotix-Pro and Arbotix-m are very different... Arbotix-Pro was made for the HR-OS1 Humanoid robot and was sort of a clone of I believe...

8 replies | 251 view(s)

1 Week Ago

KurtEck replied to a thread SetID Robotis - issue (I made a mistake) in DYNAMIXEL & Robot Actuators

I still have a few Arbotix boards sitting around here somewhere, but I don't use them for much of anything these days... For low end stuff, would...

8 replies | 251 view(s)

1 Week Ago

KurtEck replied to a thread SetID Robotis - issue (I made a mistake) in DYNAMIXEL & Robot Actuators

Not enough information here... Like how you have it hooked up, what controller, what servo... But assuming you have something that runs...

8 replies | 251 view(s)

2 Weeks Ago

KurtEck replied to a thread News/Announcement Turtlebot3 with Openmanipulator in Rovers

Glad that worked - Just in FYI - It is also in their e-manual... ...

8 replies | 1124 view(s)

2 Weeks Ago

KurtEck replied to a thread News/Announcement Turtlebot3 with Openmanipulator in Rovers

I have not done anything with mine for a few weeks now. Been busy with Puppy and with the Teensy 4 Alpha board. Sometimes when I had issues iwth...

8 replies | 1124 view(s)

3 Weeks Ago

KurtEck replied to a thread Discussion Trying to sync my MX-64T with my Arbotix-M Robocontroller. in DYNAMIXEL & Robot Actuators

Sorry, I have not used MX servos other than the MX16T, but it may help to know some additional information. Also you might get some additional help...

2 replies | 463 view(s)

KurtEck
T-1000

Mini Statistics

More 8 Friends

KevinO

r3n33

EddieB

F.I.T

ezex

minimalfra

Recent Visitors

Basic Information

Statistics

TRC Gallery

Total Posts

General Information

8 Friends

EddieB

ezex

F.I.T

KevinO

minimalfra

NicoX

r3n33

Zenta

KurtEck's Gallery

KurtEck T-1000

Mini Statistics

More 8 Friends

Recent Visitors

Basic Information

Statistics

TRC Gallery

Total Posts

General Information

8 Friends

Upload Images KurtEck's Gallery

KurtEck
T-1000

KurtEck's Gallery